The profile is bent to a template taken from the opening — the mechanism in the opening

Custom Shape Mosquito Nets in Dubai

An arched window, a round porthole, a trapezoid under a roof slope: for openings like these the screen is built to the outline rather than squared off to fit. We take the shape on site with a template, bend the profile to the radius and assemble a frame that follows the opening without gaps at the edges.

01THE JOB STARTS WITH A TEMPLATE

The surveyor holds a sheet against the opening, traces the outline and takes radii at several points: an arch cannot be built from three numbers.

02NOT EVERY COMPLICATION IS REAL

A window with corners rounded by a couple of centimetres is closed by an ordinary framed screen, and there is no reason to pay for a bent profile.

03TWO SCREENS INSTEAD OF ONE

Where an opening has both a straight and a shaped part, two are usually made: the straight one opens, the shaped one stays put. The opening keeps working and the price does not climb.

04WHAT FALLS INTO THIS CATEGORY

  • Arched villa windows and semicircular transoms over an entrance
  • Round porthole windows
  • Trapeziums under a roof pitch and raked heads by a staircase
  • Anything where a rectangular screen would leave gaps
{'ru': 'Схема: профиль гнётся по шаблону, снятому с проёма', 'en': 'Diagram: the profile is bent to a template taken from the opening', 'ar': 'رسم توضيحي: يُثنى البروفيل وفق قالب مأخوذ من الفتحة', 'hi': 'आरेख: प्रोफ़ाइल ओपनिंग से लिए टेम्पलेट पर मोड़ी जाती है'}
The profile is bent to a template taken from the opening
Shapes
arch, circle, trapezoid, free outline
Profile
bent to radius
Survey
by template, on site
Warranty
2 years

Who it suits

Suits you if

Take it when the opening is not rectangular and a rectangular screen leaves gaps. In Dubai the classic cases are arched villa windows and semicircular fanlights above an entrance door: the mosquito goes in through exactly the crescent left at the top. Round stairwell windows and trapezoids on upper floors belong here too.

Not for you if

You do not need it when the shape only looks complicated. A window with corners rounded by a couple of centimetres is closed by an ordinary framed screen, and paying for a bent profile achieves nothing. The second case is a complex shape that also has to open often. Curved mesh on a moving system is temperamental, and if the opening is in daily use it is more honest to split it into a straight opening section and a fixed shaped one.

How it works

The work starts with a template. The surveyor holds a sheet against the opening, traces the outline and takes radii at several points: an arch cannot be built from three numbers, because real openings are rarely true geometry.

The profile is bent on a machine to the radius taken. Straight runs join curved ones through corner inserts, and the joint is dressed so the mesh does not snag. The mesh is cut with an allowance and set into the groove with a cord all the way round.

Apart from the cutting and the bending, the construction is the same as a fixed frame: a rigid panel mounted into the opening on brackets. The limits are therefore the same too. A shaped screen is normally fixed; you lift it out to wash it and put it back.

Where an opening has both a straight part and an arched one, we usually make two screens. The straight one covers the sash and opens; the arched one covers the fanlight and stays put. The opening keeps working and the price does not climb.

What it costs

A shaped screen costs more than a rectangle of the same area, because a template, bending and hand cutting are added. The starting point is the same, from 200 AED per window, but the total depends on the radius and on how many curved sections are in the outline. A round window and an arch with a single radius are priced differently even when the area matches. The survey matters more here than anywhere else: an outline cannot be taken from a photograph, and we do not quote before we have been there.

An arch or a circle cannot be taken with a tape: it needs a template held against the opening and traced.

Common questions

Can I take the shape myself?

Only if you have a drawing from the window manufacturer. A tape measure on a shaped opening almost always leaves an error that shows up as a gap in the most visible place.

Can an arched screen open?

Technically yes, but we rarely recommend it. Curved mesh on a moving system wears faster. We usually make the arch fixed and let the straight part of the opening do the opening.

Can the profile be coloured?

Yes, to the RAL palette. It shows more on arched windows: a contrasting frame emphasises the curve, so most people match the window colour.

How long does it take to make?

Longer than a rectangle: a template and bending are involved. The date is given at the survey, once the outline is in front of us.

Do you do round windows?

Yes. The circle is taken with the same template, the profile is bent into a ring and the joint is placed at the bottom where it is not seen.

[ FROM SURVEY TO FITTING ]

GET AN INSTANT QUOTE

1Choose product type

2Configure dimensions

3Add options

FROM SURVEY TO FITTING

How we work

  1. Request

    You send a request here or on WhatsApp and we confirm the details in five minutes.

    Free

  2. Survey

    Our surveyor comes out free of charge and takes exact measurements of the openings.

    Same day

  3. Manufacturing

    We build the screens to your sizes in our own workshop in 24 to 48 hours.

    Quality materials

  4. Fitting

    We install and adjust the system, and it is ready to use the moment we leave.

    Careful work, no rush

CUSTOMER REVIEWS

Proof, not promises

All reviews on the Google profile →

Mosquito nets
that actually work

  • 12 years in Dubai
  • 2-year warranty

Leave a request and we will check the sizes, the type of opening and put together a tidy solution for your windows, doors or balcony

BOOK A FREE MEASUREMENT

Mosquito net on a panoramic window